TECH SUPPORT
FREQUENTLY ASKED QUESTIONS - GE CONTROLS
EV1 SYSTEM
EV-1 Panel
Question: I recently had an EV-1 Panel repaired by Flight Systems. When I installed it back in the vehicle the directional contactors close but I get no traction speed. Answer
EV100 SYSTEM
EV100LX FT and FX Cards
Question: I purchased an IC3645LXCD1FT EV100LX control card from Flight Systems but now I can't get power steering to function. Answer
EV100LX/ZX Cards
Question: I just purchased an EV100LX/ZX control card from Flight Systems but it does not function, the vehicle appears to be dead. Answer
EV100LX/ZX Cards
Question: I purchased, or had repaired, an EV100 control card from Flight Systems. There is a "Certificate of Test" sticker on the back of the control card, which says it is for 48 volt operation and my vehicle is 36 volts. Answer
EV100LX/ZX Series Controls
Question: I can not get into the programming mode when using the LX Handset. Answer
EV100 Pump Card
Question: My hydraulic pump is not working after I install a remanufactured card from FSIP, what is wrong? Answer
EV100 MA Card
Question: I just purchased an EV100 MA control card to replace my M8 control. Everything works well going straight, but if I steer in either direction, the appropriate contactor remains energized, but the vehicle stops moving. Answer
EV100 LX Cards
Question: I just replaced a GE LX control card and now I'm getting a CODE 70 or 71. Answer
EV100 LX Cards
Question: Why does my GE Handset skip functions 16-30? Answer
EV100ZX, Transistorized SEM
Question: I am trying to adjust Function 21, Regen Braking, but when it should show me the Selected Function Number U021 indicator, it gives me U053 instead. What am I doing wrong? Answer
EVT100 QP Cards
Question: I am getting code 127 and all tests in the GE manual have passed. Are there any other things I could test that would cause this code? Answer
PROGRAMMING & TROUBLESHOOTING SYSTEMS
GE Sentry Software
Question: I wanted to purchase a copy of GE Sentry software. Does FSIP sell it? Answer
GE LX Handset
Question: I'm using a GE LX Handset , how do I get to the higher functions 16-30? Answer
GE LX Handset
Question: I'm using a GE LX Handset , how do I get to the higher functions 48-63? Answer
GE Control Codes
Question: I'm getting a code when troubleshooting my vehicle with a GE Control and I don't know what it means. Answer
SX SYSTEM
IC3645SR5W606F1 For Linde Vehicle
Question: I replaced a 606F1 Motor Controller and now have NO HIGH SPEED. Answer
IC3645R3R404P3 For Crown Vehicle
Question: I'm getting a CODE 64 or 65 on my Crown vehicle. Answer
IC3645SR3R404P3 For Crown Vehicle
Question: I've installed a replacement traction control and now I'm getting a Code 68. Answer
IC3645SR3U454Z3/Z4 For Clark Vehicle
Question: I've installed a replacement traction control and now I'm getting a Code 68. Answer
IC3645SR3U454Z3/Z4 For Clark Vehicle
Question:Can my Z3/Z4 be used with different voltages? Answer
IC3645SR4T454N11 For Hyster or Yale Vehicle
Question:I've installed a replacement traction control and now I'm getting a Code 68. Answer
IC3645SR4W606N6 For Hyster or Yale Vehicle
Question: I've installed a replacement traction control and now I'm not getting high speed. Answer
IC3645SR4W10010M1Controller
Question: I replaced an IC3645SR4W10010M1 controller. I am getting code -21 after I calibrated the accelerator input, what else could be causing this code? Answer
IC3645SR4W606MC2 for Mitsubishi Vehicle
Question: I just installed a replacement control and now I'm getting a code 8 (Accelerator input volts high at start-up). Answer
IC3645SR4W746MC2 For Mitsubishi/Cat Vehicle
Question: I am having problems setting Function 11 using GE Sentry 4.07 for my SX controller. Every time I try to set Function 11, it reverts back to “0” or gives me an Error code: Integer not supported by protocol. Answer
IC3645SR7A353T4 For GEM Cars
Question: I recently received a remanufactured control for my GEM Car, I have no speed and my dash display shows “04”. Is my controller defective? Answer
